Up to date

This page is up to date for Redot 4.3. If you still find outdated information, please create an issue.

ResourceImporterWAV

Inherits: ResourceImporter < RefCounted < Object

Imports a WAV audio file for playback.

Description

WAV is an uncompressed format, which can provide higher quality compared to Ogg Vorbis and MP3. It also has the lowest CPU cost to decode. This means high numbers of WAV sounds can be played at the same time, even on low-end deviceS.

Tutorials

Properties

int

compress/mode

0

int

edit/loop_begin

0

int

edit/loop_end

-1

int

edit/loop_mode

0

bool

edit/normalize

false

bool

edit/trim

false

bool

force/8_bit

false

bool

force/max_rate

false

float

force/max_rate_hz

44100

bool

force/mono

false

Property Descriptions

int compress/mode = 0 🔗

The compression mode to use on import.

Disabled: Imports audio data without any compression. This results in the highest possible quality.

RAM (Ima-ADPCM): Performs fast lossy compression on import. Low CPU cost, but quality is noticeably decreased compared to Ogg Vorbis or even MP3.

QOA (`Quite OK Audio <https://qoaformat.org/>`__): Performs lossy compression on import. CPU cost is slightly higher than IMA-ADPCM, but quality is much higher.

int edit/loop_begin = 0 🔗

The begin loop point to use when edit/loop_mode is Forward, Ping-Pong, or Backward. This is set in samples after the beginning of the audio file.

int edit/loop_end = -1 🔗

The end loop point to use when edit/loop_mode is Forward, Ping-Pong, or Backward. This is set in samples after the beginning of the audio file. A value of -1 uses the end of the audio file as the end loop point.

int edit/loop_mode = 0 🔗

Controls how audio should loop. This is automatically read from the WAV metadata on import.

Disabled: Don't loop audio, even if metadata indicates the file should be played back looping.

Forward: Standard audio looping.

Ping-Pong: Play audio forward until it's done playing, then play it backward and repeat. This is similar to mirrored texture repeat, but for audio.

Backward: Play audio in reverse and loop back to the end when done playing.

Note: In AudioStreamPlayer, the AudioStreamPlayer.finished signal won't be emitted for looping audio when it reaches the end of the audio file, as the audio will keep playing indefinitely.

bool edit/normalize = false 🔗

If true, normalize the audio volume so that its peak volume is equal to 0 dB. When enabled, normalization will make audio sound louder depending on its original peak volume.

bool edit/trim = false 🔗

If true, automatically trim the beginning and end of the audio if it's lower than -50 dB after normalization (see edit/normalize). This prevents having files with silence at the beginning or end, which increases their size unnecessarily and adds latency to the moment they are played back. A fade-in/fade-out period of 500 samples is also used during trimming to avoid audible pops.

bool force/8_bit = false 🔗

If true, forces the imported audio to use 8-bit quantization if the source file is 16-bit or higher.

Enabling this is generally not recommended, as 8-bit quantization decreases audio quality significantly. If you need smaller file sizes, consider using Ogg Vorbis or MP3 audio instead.

bool force/max_rate = false 🔗

If set to a value greater than 0, forces the audio's sample rate to be reduced to a value lower than or equal to the value specified in force/max_rate_hz.

This can decrease file size noticeably on certain sounds, without impacting quality depending on the actual sound's contents. See Best practices for more information.

float force/max_rate_hz = 44100 🔗

The frequency to limit the imported audio sample to (in Hz). Only effective if force/max_rate is true.

bool force/mono = false 🔗

If true, forces the imported audio to be mono if the source file is stereo. This decreases the file size by 50% by merging the two channels into one.